MAN B&W 48/60B Engine
The current basic family of MAN B&W's large medium- speed diesel engines consists of four sizes L 58/64, L/V 48/60, L 40/54 and L/V 32/40, launched between 1985 and 1995. This engine family covers an output range from 2,880 kW (6L 32/40) to 18,900 kW (18V 48/60). Within the last few years, this portfolio has been supplemented by the V 40/50, the smaller engine sizes L 16/24 and L 27/38, and, finally, the new L 21/31 (2002/03). All engines are fully heavy fuel oil compatible and have been optimized for both high fuel economy and lowest exhaust gas emissions.
In terms erf sold power, the 48/60 engine is second in the list of MAN B&W's bestsellers. Since its market launch in 1989 to January 31, 2002, a total of 245 engines of this size, representing 3.7 million hp, has been sold, of which 162 engines were for marine applications The 48/60 has evolved with the needs of the market in its 13 years. Service experience and improvement in component design are just two reasons driving change.
In addition, progress is made in better understanding injection, combustion and emission control. Both theoretical and experimental development work result in greater insights into the many processes involved, allow safe prediction of component loadings, safety levels and even lifetimes. With all this experience and knowledge at hand, it is possible today to upgrade an existing proven engine in regards of output, fuel consumption, emissions, and component safety, whilst retaining proven engine sub-groups.
For these reasons MAN B&W decided to retain the main dimensions, bore and stroke, of the 48/60 and with it many proven engine subgroups, while modifying and changing a variety of other key engine components.
The new engine is named 48/60B. with a rating of 1,200 kW per cylinder at 500 and 514 rpm. respectively. This is equal to an increase of 14 percent over the current nominal output of the 48/60 engine.
The 48/60 B also is cleaner and leaner, featuring: • Increased efficiency (fuel savings, lower carbon dioxide emission) • Less smoke and nitrogen oxides • Reduction in engine width and. consequently, in center-to-center distance in order to reduce the gear size • Improved operational and component reliability • Increased ease of maintenance • Reduction in weight-to-power ratio • Reduction of manufacturing costs by applying improved design features and a lower number of engine components and parts.
Achieving Better Fuel Economy With a bore of 480 mm and a stroke of 600 mm (bore-to-stroke ratio = 1.25), the 48/60B engine obviously is not a typical long-stroke engine with its options to reduce fuel consumption rates. However, even with the same bore-to-stroke ratio, the bundle of in-engine measures effected gave the same result — at a lower cost. A package of engine-internal measures was worked out, initially confirmed to be feasible by simulation calculations and finally tested step by step on a 12V 48/60B protopype engine in order to find the best solution between several variables, i.e. an acceptable compromise between fuel consumption, component loading, and NOx and smoke emissions.
To achieve this target, the following principal correlations, which are partly in conflict with each other, had to be considered and the work process was modified accordingly: 1. Adoption of a "slight" Miller process to lower combustion temperature levels, and, with them, NOx emission.
2. Increase in injection intensity for lower soot production and therefore lower smoke emissions, especially at partload. Unfortunately, this measure has a negative effect on NOx emission. In order to neutralise the increase in NOx emission, the injection can be retarded, although this leads to a higher fuel con-sumption rate and increased particle emission.
3. To neutralize the fuel consumption disadvantage resulting from step (2), it is necessary to take advantage of the firing pressure potential of the engine.
Therefore a higher compression ratio has been chosen for the 48/60B.
4. Use of the considerably increased efficiency level of the newly-designed MAN B&W TCA-type turbocharger so that the resultant fuel savings from steps (1) to (3) exceeded the fuel losses involved in (1) to (3).
By optimizing the combustion space geometry (with unchanged engine stroke), which was achieved by avoiding dead volumes, edges and ribs in the combustion side of the cylinder cover, the compression ratio was increased from e = 14.4 (48/60) to e = 15.3 (48/60B). A possible further increase in e would most likely result in increased smoke emission at low loads. A conventional medium-speed diesel engine with a bore-to-stroke ratio of 1.25 and a rather high compression ratio of, for instance e = 17, would produce a pronounced dark plume — even at higher engine loads - which would be visible from far away.
The slightly increased compression ratio of the 48/60B has another beneficial effect: it improves the ignition behaviour of lowest-quality heavy fuel oils. The 48/60B can there-fore safely operate with HFO up to a viscosity of 700 cSt/50°C and runs on fuels up to, and including, the CIMAC H55/K55 specifications.
Cylinder Head Design The firing pressure of the 48/60B was increased to a maximum of 200 bar. This, in c o n - n e c t i o n with other measures such as modified injection (the injection pressure was in-creased from 1,300 bar for the 48/60 to 1,600 bar) and a f u r t h e r improved gas exchange process, resulted in a process very close to the ideal constant-pressure combustion. The higher firing pressure was possible without risking the operational safety of the engine: to have the same safety margins as the 48/60 in spite of a higher mechanical loading, better materials were used and/or com ponents strengthened.
An engine component considerably contributing to make this engine setting easier is the newly designed TCA axialflow turbocharger from MAN B&W Diesel in Augsburg, Ger-many. Compared with the previous turbocharger generation (NA/S-type series), TCA turbochargers show increased airflow rates, higher compressor pressure ratios and.
simultaneously, significantly higher turbocharger efficiencies across the whole load range. The most obvious benefits from this are greater flexibility in matching the turbo-charger to the engine, a higher surge margin and improvements in the engine's scavenging process. The TCA turbocharger can be easily optimised for higher charge-air pressures at part load for best fuel con- sumption, for lower pollutant emissions and for a quick load response.
The minimum fuel consumption rate, at 85 percent engine load, and in constant speed application, is 173 g/kWh, which is 7 g/kWh better than that of the 48/60 Vee-type engine at the same absolute output. Simultaneously, the measured smoke Bosch index, from full load down to about 20 percent engine load, is below 0.3 — which means invisible soot-produced exhaust.
With such favorable smoke emission figures, the new 48/60B is a genuine Invisible Smoke (IS-type) engine, a result that has been achieved only with inbuilt emission-reduction technologies, omitting additional hardware such as an auxiliary air blower.
Engine design Since bore and stroke of the 48/60B remained unchanged, the robust and stiff single-part engine block of the current 48/60-type engine, cast of grey iron or nodular iron, could be used with sufficient operational and safety reserves.
The main features of the basic engine structure are the same for all MAN B&W medium-speed diesel engines: cylinder jackets separated from each other and mounted on the frame, and an un-derslung crankshaft. The engine cooling water is only supplied to these jackets, leaving the engine frame itself completely free from cooling water.
Therefore the risk of lube oil contamination by water is avoided.
Other design features include: Changed turbocharger/charge-air cooler mounting to decrease engine width of all 48/60B Vee-type engines.
The center-to-center distance between two V48/60B-type engines was decreased by about 1 m.The total height of the engines is the same as with the current 48/60 models.
• Re-designed cylinder head without valve cages and a new valve train • Modified valve timing • New injection system with high injection intensity (as described above) • Improved piston with a steel crown and a skirt cast of nodular iron or a steel skirt • Improved material for the connecting rod. and increased shaft diameter • New combustion chamber.
The new engine also features a simplified exhaust-gas system with only one single exhaust manifold and a single (TCA) turbocharger for Vee-version engines, improving access to engine components, reducing the number of component variants, and contributing to a reduction in engine mass. For instance, the dry weight of the 14.4 MW 12V 48/60B engine is 181 tons compared with 193 tons for the current 12V 48/60 that is rated at only 12.6 MW.
Another example for new inventions with the 48/60B is the patented rocker arm concept with the modified rocker arm. The axial bearing of the rocker arm was replaced by two spherically shaped bearings. With this solution the number of moving parts is reduced from three to two. Accordingly, the valve train assembly is less complicated than in the current 48/60. Rocker arm housing and charge-air pipe section made of aluminium form one common casing. This allows easy dismantling, reduced maintenance work for the rocker arms and the rocker casing. To meet the higher mechanical load, special attention was paid to the conrod bearing. Its big-end design was improved by: modified bearing shell concavity and optimized bearing clearance.
Circle 190 on Reader Service C a rd w w w . m a r i t i m e r e p o r t e r i n f o . c om The preceding was excerpted from a paper by Horst W. Koehler, MAN B& W Diesel
Other stories from July 2002 issue
- Zodiac Debuts Bulletproof System For CRRC page: 5
- Historic $17 Billion Order Placed page: 6
- USCG Proposes New Changes in Vessel Arrival/Departure Procedures page: 9
- NASSCO Celebrates Keel Laying of Trailerships page: 11
- Industry-Wide Interoperability Investment Paying Off page: 12
- Tribon M2 Aim: Better Ships at a Lower Cost page: 14
- Total CAD/CAM Solution for Ship Design and Building page: 15
- Juniper Industries Keeps the Water Out page: 17
- Molding the five-deck Trailership page: 18
- IZAR Gijon Delivers Dredger page: 19
- Estonians Raise the Ferry Stakes page: 19
- Transportation Secretary Announces $92.3M in Port Security Grants page: 21
- USS Shoup Commissioned page: 23
- U.K. Royal Navy Increases Overhaul Efficiency of HP Air Cylinders page: 24
- DD(X) Dispute: BIW Files Protest page: 25
- Technological Wonder, No Matter How You SLICE It page: 26
- GALILEO: 2008 or Bust? page: 28
- Forget the Dog, MTN Delivers the News Onboard Residensea page: 29
- SeaWave Aims to Drive Down Communication Costs page: 29
- Iridium Aggressively Pursues New Outlets page: 30
- Fincantieri Stays Strong page: 32
- Fincantieri Predicts Clear Vista For HAL page: 32
- Rodriquez Cantieri Navali: Fast Company page: 33
- SEA RIDER Infiltrates Small Craft Propulsion Market page: 34
- ACG Makes Solid Inroads page: 35
- SubSea Solutions Alliance Provides Quick Fix - Underwater page: 36
- Classic Vessel's Demise Lead to New Found Hobby page: 38
- STAR Center Provides 360-Degree Field of View page: 41
- MAN B&W 48/60B Engine page: 42
- Titan Pulls One Off for Marine Response Alliance page: 54