Page 33: of Maritime Reporter Magazine (July 1981)
Read this page in Pdf, Flash or Html5 edition of July 1981 Maritime Reporter Magazine
MEGATOR L-400 4"X4"
BILGE & BALLAST PUMP
Sliding shoe—self-priming. 240 GPM — 45 PSI. MOTOR: 15 HP 440/3/60/1750 RPM.
MEGATOR L-125 l^'Xl1/*"
FRESH WATER PUMP
W
Sliding shoe—self-priming. 20 GPM-45 PSI—11/2 HP— 440/3/60 - 1750 RPM.
OTHER MEGATOR PUMPS
L-150 FOR SANITARY SERVICE 40 GPM-45 lbs-l'/2"XIV2"-3 HP-440/3/60-1750
RPM. Self-Priming.
H-125 FOR GENERAL SERVICE 20 GPM-75 PSI-l'/4"Xl'/4"-2 HP — 440/3/60. Self- priming.
L-300 FUEL OIL TRANSFER
BILGE & BALLAST 120 GPM-45 PSI-3"X3"-7'/2 HP-440/3/60-1750
RPM. Self-Priming.
LINK BELT WINDLASS
NEW m - ^ UNUSED
Handles 7000 lb anchors — 1W windlass — 56" centers — 50 HP — 230 VDC — with controls and spares. located at . 21230
NEW PHONE (301) 752-1077 n us
CO. • BALTIMORE, MD. 21202 900 Marine Dept.: (301) 752-1077 ^D. U.S.A. TWX 710-234-1637
PUMPS
GORMAN RUPP TYPE
BILGE SERVICE PUMP if; -i-; -—JL
Size 4—70 GPM @ 60 PSI—for raw sewage overboard service. 7V2 HP.
GORMAN RUPP OVERBOARD
DISCHARGE TRASH PUMP
Self-priming—50 GPM @ 25 PSI-2"X1'A"-1.5 HP- 220/440/3/60-3450 RPM. Model 13A2B.
NEW - UNUSED
NIJUIS FIRE PUMP 5-STAGE 5" X 3' 550 GPM (a) 323' head (5) 1800 RPM
I.T.T. MARLOW EMERGENCY
BILGE & BALLAST PUMP
Self-priming—3"X3"—150 GPM @ 150' head. Model 37HEL-15E. RELIANCE MOTOR: 15 HP-440/3/60-3505
RPM.
GOULD HIGH PRESSURE
WATER INJECTION PUMP
STAGE 1: Gould Figure 3755 - 3X4X7 - 150 PSI- #700B396. STAGE 2: Gould Finure 3316-4X6X11- #224B-274. MOTOR: Double shaft - 200 HP Westing- house - 440/3/60 - 3550 RPM. Frame 444 T5 - style 680B400GMI.
WITH SPARE MOTOR
FACTORY NEW
NIJUIS 10"X8" SPLIT CASE
HORIZONTAL PUMPS •«««»»>. a :|T ' f
Best efficiency 3400 GPM @ 160 PSI-1500
RPM or 5220 GPM @ 30 PSI-1500 RPM maximum capacity. 4500 GPM @ 125 PSI 1800—RPM. Requires 500 HP. 2000 GPM @ 110 PSI—1450 RPM (using 6-V-71 en- gine reducing 8" to 6" suction).
GENERAL PURPOSE WINCH 3500 LBS AT 200 FPM
CARGO WINCH - UNUSED 2-DRUM 2-GYPSY DECLUTCHABLE
A 1
DUTY: 7400 LBS @ 220 FPM. Mfg by Western Gear
Works. With repair parts. Model CWE50. Capacity of each drum 600 ft. of wire rope. MOTOR: 50 HP— 230 VDC with control. 14" Cutler-Hammer brake con- trol — 1 master switch — enclosed contactor panel & resistors.
LARGE STEAM
TOWING ENGINE 9 X 10 TWIN ENGINE DRIVE
Air or Steam - 125/250 PSI
Heavy-duty Clyde with 36" diameter X 51" Face single drum. Flanges 68". CAPACITY: Up to 2800' of 2" wire rope. Normal line pull 40,000 lbs@ 50 FPM. Steam or air pressure required 125 to 250 PSI. Can be adapted to electric drive or increased steam or air pressure to a capacity of 82,000 lbs @ 20 FPM. Pawl holds 270,000 lb. pull from any layer. Equipped with level wind device. Approximate weight 30,000. DIMENSIONS: 12'6" wide—6'6" high. Write for details.
ALSO AVAILABLE
Large towing ring — 36" I.D. |3r
A.C. Motor drive—25/12.5 HP-GE 440/3/60-40 °C AB — 1750 RPM—type KR—full load amps 32. Motor drives winch through Folk reduction gear. Has compressor hand brake.