Page 29: of Maritime Reporter Magazine (July 15, 1981)

STEAM MOORING WINCHES 12" x 14" - STEAM OR AIR DRIVEN with foot brake & declutchable gypsy head 20,000 LBS @ 100 FPM—FIRST LAYER

ALSO HANDLES 16,000 LBS @ 150 FPM

OR 50,000 LBS @ 8 FPM

Drum will show 1500 ft of T/j" wire in 9 layers. Steam inlet 3'/j" — 4" exhaust—171 PSI working pressure.

BASE DIMENSIONS: 6' x 6' V/2" - overall 8' 4Vj" wide x 9' long. Mfg by Friedrich Kocks — Bremen, Germany.

Recently removed from ARCO "Challenger".

ALSO IN STOCK 12" x 14" Double Gypsy Unit

All UNITS CAN BE DEMONSTRATED RUNNING

NEW - UNUSED

LINK BELT WINDLASS

Handles 7000 lb anchors—windlass —56" centers — 50 HP — 230 VDC — with controls and spares.

NEW - UNUSED - EX-U.S.N. 100,000 LB. ALMON JOHNSON

Constant Tension Mooring Winches

In very good condition. Series 232 mooring & anchor- ing winches. Automatic self-tensioning. Wide range from 100,000 lb. line pull @ 10 FPM to 26,000 lbs. @ 400 FPM. Gypsy line pull @ 12,000 lbs. @ 25

FPM. Drum declutchable through spiral jaw clutch for free spooling. Driven by 50 HP 230 VDC motors —

Westinghouse CK - 575 RPM —'/2 hour —75°C rise— stab shunt — 181 amps. Max. RPM 1900 — Cutler-

Hammer brake — 18" — type NM. Complete with mag- netic control panel, resistor banks & remote control pedestal and mounted master switch. v located at

Md. 21230

NEW PHONE (301) 752-1077 m us

CO.

ST. • BALTIMORE, MD. 21202 539-1900 Marine Dept.: (301) 752-1077

RE, MD. U.S.A. TWX 710-234-1637

LARGE STEAM

TOWING ENGINE 9 X 10 TWIN ENGINE DRIVE

Air or Steam - 125/250 PSI

Heavy-duty Clyde with 36" diameter X 51" Face single drum. Flanges 68". CAPACITY: Up to 2800' of 2" wire rope. Normal line pull 40,000 lbs@ 50 FPM. Steam or air pressure required 125 to 250 PSI. Can be adapted to electric drive or increased steam or air pressure to a capacity of 82,000 lbs @ 20 FPM. Pawl holds 270,000 lb. pull from any layer. Equipped with level wind device. Approximate weight 30,000. DIMENSIONS: 12'6" wide—6'6" high. Write for details.

ALSO AVAILABLE

Large towing ring — 36" I.D. 60KW DIESEL GEN. SET

DELCO GEN. — GM 6-71 DIESEL

Delco 120 volt DC 500 amp stab, shunt 1200 RPM gen- erator. Engine is GM 6-71 — heat exchanger cooled.

Radiator shown is not included.

Reconditioned — Ready To Go. 300KW GM 8-268A 120/240 DC

DIESEL GEN. SET m

ENGINE: GM 8-268A - 6Vi X 7 - 1200 RPM. Heat exchanger cooled. GENERATOR: Westinghouse 300 KW — 120/240 DC — shunt wound.

PRICED RIGHT

STANDBY GENERATOR

CUMMINS 75KW 93.8 KVA

DIESEL GENERATOR SET 440/3/60 Generator—1200 RPM—driven by 6-cylinder

Cummins diesel with electric starting. Free standing switchgear. $9750 40KW EMERGENCY GEN. PANEL

Provides necessary device for automatic startup, con- trol & protection of emergency generator. Provides power for essential circuits in case of failure of pri- mary source. Also automatic shutdown of generator on restoration of primary source of power.

NAVY AXIAL FLOW FANS 10,000 CFM—A10A4-W5. 20" ID. MOTOR: 7.5/3.3 HP- 440/3/60- 10.5/5.2 amps - 1750/1150 RPM. Recondi- tioned — 9 available.

ALSO 1 20,000 CFM FAN AVAILABLE 2500 LBs @ 125 FPM on one gypsy head or 1250 lbs @ 125 FPM simultaneously on each gypsy. MOTOR: 15 HP—230 volts DC—55 amps-GE. AVAILABLE: 1 Set mfg by Lakeshore with Reliance motor—1 set mfg by

Ideal with GE motor. Complete with controls and disc brake.

A.C. Motor drive—25/12.5 HP-GE 440/3/60-40 °C AB — 1750 RPM—type KR—full load amps 32. Motor drives winch through Falk reduction gear. Has compressor hand brake.

CARGO WINCH-NEW-UNUSED 2-DRUM 2-GYPSY DECLUTCHABLE

EX

U.S.N.

DUTY: 7400 LBS @ 220 FPM. Mfg by Western Gear

Works. With repair parts. Model CWE50. Capacity of each drum 600 ft. of W wire rope. MOTOR: 50 HP— 230 VDC with control. 14" Curier-Hammer brake con- trol — 1 master switch — enclosed contactor panel & resistors.

BATHYTHERMOGRAPH WINCH

GENERAL PURPOSE WINCH 3500 LBS AT 200 FPM

TYPE

C.T.B. 10318

NEW - UNUSED - IN ORIGINAL CRATE

BOAT HANDLING AND

GENERAL PURPOSE WINCH

EX

U.S.N.

NEW

UNUSED

EX

U.S.N.