Page 41: of Maritime Reporter Magazine (September 1981)

STEAM MOORING WINCHES 12" x 14" - STEAM OR AIR DRIVEN with foot brake & declutchable gypsy head 20,000 LBS @ 100 FPM—FIRST LAYER

ALSO HANDLES 16,000 LBS @ 150 FPM

OR 50,000 LBS @ 8 FPM

Drum will show 1500 ft of 1 Vi" wire in 9 layers. Steam inlet 3'/j" - 4" exhaust— 171 PSI working pressure.

BASE DIMENSIONS: 6' x 6' 3'/s" - overall 8' 4Vi" wide x 9' long. Mfg by Friedrich Kocks — Bremen, Germany.

Recently removed from ARCO "Challenger".

ALSO IN STOCK 12" x 14" Double Gypsy Unit

ALL UNITS CAN BE DEMONSTRATED RUNNING

NEW - UNUSED

LINK BELT WINDLASS

Handles 7000 lb anchors —windlass —56" canters — 50 HP — 230 VDC — with controls and spares.

NEW - UNUSED - EX-U.S.N. 100,000 LB. ALMON JOHNSON

Constant Tension Mooring Winches

In very good condition. Series 232 mooring & anchor- ing winches. Automatic self-tensioning. Wide range from 100,000 lb. line pull @ 10 FPM to 26,000 lbs. @ 400 FPM. Gypsy line pull @ 12,000 lbs. @ 25

FPM. Drum declutchable through spiral jaw clutch for free spooling. Driven by 50 HP 230 VDC motors -

Westinghouse CK - 575 RPM — V? hour — 75°C rise— stob shunt — 181 amps. Max. RPM 1900 — Cutler-

Hammer brake — 18" — type NM. Complete with mag- netic control panel, resistor banks & remote control pedestal and mounted master switch. located at

NEW PHONE (301)

Md. 21230 S 752-1077 )n us

CO.

ST. • BALTIMORE, MD. 21202 39-1900 Marine Dept.: (301) 752-1077

MD. U.S.A. TWX 710-234-1637

LARGE STEAM

TOWING ENGINE 9 X 10 TWIN ENGINE DRIVE

Air or Steam - 125/250 PSI

Heavy-duty Clyde with 36" diameter X 51" Face single drum. Flanges 68". CAPACITY: Up to 2800' of 2" wire rope. Normal line pull 40,000 lbs@ 50 FPM. Steam or air pressure required 125 to 250 PSI. Can be adapted to electric drive or increased steam or air pressure to a capacity of 82,000 lbs @ 20 FPM. Pawl holds 270,000 lb. pull from any layer. Equipped with level wind device. Approximate weight 30,000. DIMENSIONS: 12'6" wide—6'6" high. Write for details.

ALSO AVAILABLE

Large towing ring — 36" I.D. 60KW DIESEL GEN. SET

DELCO GEN. - GM 6-71 DIESEL

I r A II • I | m ' •lili £ dSSlnsi' • ;

V

Delco 120 volt DC 500 amp stab. shunt 1200 RPM gen- erator. Engine is GM 6-71 — heat exchanger cooled.

Radiator shown is not included.

Reconditioned — Ready To Go.

GENERAL PURPOSE WINCH 3500 LBS AT 200 FPM

A C. Motor drive—25/12.5 HP-GE 440/3/60-40°C AB —1750 RPM—type KR—full load amps 32. Motor drives winch through Falk reduction gear. Has compressor hand brake.

CARGO WINCH-NEW-UNUSED 2-DRUM 2-GYPSY DECLUTCHABLE hmm |«"» 6t Lfclif«,! P slag

DUTY: 7400 LBS @ 220 FPM. Mfg by Western Gear

Works. With repair parts. Model CWE50. Capacity of each drum 600 ft. of 3A" wire rope. MOTOR: 50 HP— 230 VDC with control. 14" Cutler-Hammer brake con- trol — 1 master switch — enclosed contactor panel & resistors.

NEW HAYWARD

DUPLEX STRAINERS

Cast Steel - (1) 6" - (2) 8"

Bronze - (1) 4" 2 NEW - UNUSED

ACCOMMODATION LADDERS 38' LONG - 24" WIDE

Self-feathering — with handrails on both sides. (Less turntables) $6750

ROSS COOLER - SIZE 1042

Single pass — with W Cupro nickel tubes, tube sheets and heads. Steel shell. IVi" water inlet — 2Vz" oil inlet. Overall length 55" — 38" tube length.

NAVY AXIAL FLOW FANS 10,000 CFM-A10A4-W5. 20" ID. MOTOR: 7.5/3.3 HP- 440/3/60- 10.5/5.2 amps - 1750/1150 RPM. Recondi- tioned — 9 available.

ALSO 1 20,000 CFM FAN AVAILABLE

NEW - UNUSED

AXIAL FLOW FANS • 6000 CFM — 3 HP - 440/3/60 • 10,500 CFM - 5 HP - 440/3/60 - 1250 RPM • 12,800 CFM - 7/1.9 HP - 440/3/60 - 1750 RPM

FAIRLEADS

NEW-UNUSED 4-ROLLER TYPE

UNIVERSAL SHIPBOARD FAIRLEADS

Opening between vertical rollers 10" — between hori- zontal rollers 4". Roller size 7Vz" — pin size 2V2".

Rollers 24" long. Extended legs for welding to deck.

All are I8V4" x 33V2" at top angled to 44" x 46"2" at bottom. 7/s" Steel. Rollers have grease fittings. Plans available on request. SUITABLE FOR VESSELS UP TO 200,000 TONS. WIRE SIZE UP TO 5" CIRCUMFERENCE

OR 95 TONS, NORMAL BREAKING STRENGTH. MAX-

IMUM LEAD 80°. 6 ROLLER TYPE

MOORING FAIRLEADS

WITH 12" CLEAR OPENING 4 Vertical rollers — 5Vi" diam- eter—2 horizontal rollers—5V2" diameter, split to enable work- ing from either end of fair- lead. Steel sideframe top & bottom 1". Handles IV2" wire easily—up to maximum lead 80°.